tips should help you with framing a basic project around your home. Framing
a house should be left to an experienced framing crew. (Photo10)A good
framing job will make the entire rest of the job come out better. There
is nothing worse than having to redo something when there is a problem
caused by inaccurate framing.
exterior walls is a pretty straightforward process. Assembling walls on
a level surface - probably the subfloor or slab - and raising them into
place will help you frame faster. However, raising walls usually requires
some extra help.
walls are 8' to 12' high. Older homes and warmer climates will have 2x4
wall studs. Newer homes in colder climates will use 2x6s, to create more
space for insulation.
Framing consists of top and bottom plates, wall studs and headers, with
trimmers and king studs as needed for window and door openings.
TIP: Before starting the layout process,
chalk line the locations of the walls and their window/door openings on
the subfloor. These marks will enable you to visualize and check the project's
layout before the walls are made. The chalklines also serve as guidelines
when actually raising the walls into place.
Marking Top & Bottom Plates
Wall studs are
generally spaced 16" on center (O.C.). (Photo2) Set the bottom (sole)
plate and top plate flat. The first stud will sit on the end of the plate.
Measure and mark 15-1/4" from the end for the near edge of the second
stud. From this mark make marks every 16" for the near edges of the
remaining studs. (The reduced spacing between the first and second studs
ensures that a 4-foot-wide piece of sheathing can be flush with the outside
edge of the first stud but land in the center of the fourth stud.)
Where possible, on walls that run perpendicular to the floor joists, lay
out the studs to line up over the floor joists for more structural strength.
Most plans call
for two top plate layers. Fit the second cap plate on the top plate, but
cut it short to leave the ends exposed. After the walls are set you'll
be able to overlap the corner joints.
Cutting Wall Studs
Inspect the straightness
of your wall studs before cutting them. Try to skip over ones with bad
warps or twists, because they're hard to nail flush and can throw the
stud spacing off. Keep them in mind for trimmers or cripple studs.
Wall studs can be cut out of standard lengths of 2x lumber. We like our
walls to be 8' 1" high (from the top of the subfloor to the underside
of the ceiling joists). With a 1/2" or 5/8" layer of drywall
on the ceilings, two horizontal rows of 4' wide drywall on the walls,
this will leave a gap of about 1/2" between the bottom of the lower
row of drywall and the subfloor. Pre-cut studs are available 92-5/8"
long to accommodate this wall height.
you're not using precut studs, cutting them to length can be done all
at once. This saves a little time, but test fit and measure the first
few studs to make sure they're the right length.
Assembling Walls & Corner Posts
We usually assemble the wall on the floor, nail it together, then raise
it into place. Working on a level surface is a major help in laying out
the walls flush. Try to avoid assembling walls on the ground and keep
the work surface clean by sweeping it periodically.
Lay out the bottom and top plates on edge. Between the plates, insert
the wall studs on their marks and nail the end studs in place. Once the
wall is square, nail on the remaining wall studs.
NOTE: It's a good idea to check for squareness
by measuring diagonally from the corners after nailing on each end and
after each wall is assembled.
two walls meet in a corner there needs to be some extra framing to make
sure that there's something on each wall for the drywall on both walls
to nail into. One wall at every corner needs a corner "post."
Here are two ways to create one:
1) Add 2x4 spacer
blocks between the end stud and then install an extra "corner stud."
2) Lay an extra corner stud sideways, flush with the inside edge of the
Once the corner post is secure, insulate the cavity before installing
the sheathing. Once the sheathing is on and the wall goes up, the end
of one wall section will cover the corner of the other making insulating
impossible at that point.
Laying Out Window/Door Openings
Most walls include
a door or window opening. Additional framing support is needed to transfer
the structural weight over the opening and down to the floor. This framing
is done with trimmer, king and cripple studs and a header.
On the top and bottom plates, mark the center of the window/door rough
opening. An architect's plan will indicate where they go in relation to
the corners, but double-check to make sure the openings are in the right
Divide the opening widths in half and measure each direction from the
center. These marks indicate where the inside edge of the trimmer studs
Cut the trimmers for the height of the rough window or door opening. Then
nail them to full height king studs and install them together. They're
easier to handle this way and you can plumb them in place in one step.
Find the header
length by measuring between the king studs. The header must be sized to
meet local building codes. For single window or door openings two 2x10s
nailed to each other often provide enough strength. Wider openings may
require LVLs. Your lumber yard or home center may offer guidelines and
material suggestions for different width openings.
the header in place, nailing through the king studs into the ends of the
headers. Fit cripple studs on 16" centers above the header. In some
cases the header may end up too close to the top plate to use cripple
studs. So, that space must be filled with lumber of that thickness.
For windows, a sill plate at the bottom of the opening is nailed into
the trimmers and supported by cripple studs under the sill plate on 16"
Nailing On Sheathing
either 4x8 (or 4x9) oriented strand board or plywood sheets, is nailed
to the framed wall.
It's always easier to nail on sheathing before raising the walls, but
a lot of the time you will have to nail the sheathing in place.
(Photo8)The added weight on the wall is sometimes too much for two people
to handle. So get extra help in raising the wall. It still beats working
off a ladder and trying to nail up 4x8 sheets.
up the sheets so the seams run down the middle of the studs. This way
each piece will have a 3/4" surface to nail to. When you lay out
the sheets, utilize the straight factory edges. Eliminate slight bows
in the wall studs by pushing them to run evenly with the edge, then nail
the sheathing in place.
NOTE: Give a lot of attention to making straight
cuts. You'll probably need to use some of these scrap pieces and they'll
fit better with straight edges.
Raising & Bracing Walls
Now the wall
is ready to be raised. This may require some extra muscle, so get a few
people to help out.
With the wall still laying flat, position the bottom plate on a previously
made chalkline mark (its width from the edge). Tack the bottom plate by
toenailing a few nails through the top of the bottom plate to the subfloor.
Slowly walk the
wall upright. The tack nails will help hold the wall in place. Tap the
wall flush and square it into place with a sledgehammer. Nail the bottom
plate to the subfloor -- into the floor joists if possible.
When the wall
sections are nailed together, additional corner bracing is needed until
the roof is framed to keep the walls from swaying.
Overlapping the corner joints, nail the remaining cap plate sections on
the top plates. You may be able to take some slight bows out of the top
plates, but they'll need bracing.
a stringline to check how straight the top plate is. Straighten any top
plate bowing by pushing a brace board into the plate until it's flush.
Anchor the brace by nailing it to a stake driven into the ground.
Place 2x4s diagonally from the top corners to the rim joist, a long brace
on one side and a short brace on the other. However, this is just a guideline.
You may need even more bracing for your project.
to Topics Page